FB Surface Aerators

BIOLOGICAL TREATMENT > FB Surface Aerators

INTRODUCTION:

A correct design of the biological treatment is fundamental for the success in the fulfillment of the parameters of the WWTP output. In the case of installing FB surface aerators at this stage, they will have access to the best compromise between the oxygen transfer required for bacterial respiration and adequate agitation of the reactor, depending on the size of the reactor, since there is a wide range of impellers that can be installed with the same power and flexibility is sought when adapting to reactors that have different aeration volumes under the same power requirements.

In addition, the drive units are selected under strict criteria, bearing in mind the most adverse conditions and always looking for a product durability that experience supports, being available drive options through two-speed motors that allow significant energy savings.

DESCRIPTION:

The FB surface aerator is an open type impeller, suitable for working with solids of various sizes. It is basically composed of a tubular shaft, an inverted cone and a certain number of driving blades, which are tangential to the central tubular shaft. The impeller is made of electrowelded steel.

For the selection of the most suitable impeller size for the particular application, the oxygen requirements of the tips and the volume of the aeration chamber must be taken into account.

The FB surface aerator is an open type turbine, to be installed on the gangway and with a low speed range, suitable for working without problems in the presence of solids, with different models available. For the selection of the appropriate impeller size, the installed power, the size of the basin and the peripheral speed of the rotor must be taken into account.

The impeller of the aerator, when rotating, evacuates with its blades the existing fluid around it. The evacuated fluid is continuously replaced by the fluid that occupies the base of the aerator, generating a suction from the bottom of the tank and combining a toroidal and circular movement of the entire liquid mass. In this way, a renewal of the tank surface is achieved, and speed gradients keep the activated sludge in suspension.

The surface aerator can be used in all existing activated sludge processes as well as in aerobic sludge digestion. The slower models are especially suitable for use in Carousel type systems, due to the high flow rate provided.

GENERAL DIMENSIONS:

CLIENTE / CUSTOMER

CANT./QTY

PROYECTO / PROJECT

AGUAS FILTRADAS

1

Casino Madrid
ABENSUR

6

Paine/Chile
ABENSUR

4

EDAR Las Cabezas de San Juan
ASTEISA

1

Etap Talaveruela
APLICACIONES FB

1

Urb. Pinar de Puenteviejo
APLICACIONES FB

1

Carcel de Meco
APLICACIONES FB

4

Azucarera de Olmedo
CUBIERTAS

4

Guadix
CUBIERTAS

2

Padrón
DINOTEC

4

Edar Torredelcampo
DINOTEC

2

EBAR SAN GEOLIT Y AMP. EDAR MENGIBAR
DINOTEC

1

EBAR SAN GEOLIT Y AMP. EDAR MENGIBAR
DTD

2

S. Roque
DYTRAS

2

Aeropuerto de Gerona
DYTRAS

4

Aracena
DYTRAS

6

Ayamonte
DYTRAS

4

Alcalá la Real
DYTRAS

6

Baza
DYTRAS

1

Huerta – Blanquillo
DYTRAS

4

Edar de Moraleja
DYTRAS

4

Edars Moguer y San Juan
DYTRAS

4

Campillos
DYTRAS

4

Fines
DYTRAS

6

Montilla
DYTRAS

6

La Carolina
DYTRAS

1

Doñana Bonares
DYTRAS

2

La Palma del Condado
DYTRAS

8

Medina Sidonia
DYTRAS

8

EDAR SUCEAVA
DYTRAS

10

EDAR SLOBOZIA (RUMANIA)
DYTRAS

2

EDAR DE PARQUE EMPRESARIAL ALHENDIN
ECOPRENEUR

1

La Ramirana
ECOPRENEUR

5

Esval/Chile
ESAUNE

1

Fábrica de Esaune
ESPINA OBRAS HIDRAÚLICAS

6

Edar en Trinidad
FERROVIAL-ASTEISA U.T.E.

1

Villanueva de la Serena
GTT INGENIERIA

1

Benferri Lamurada
IMFLUID

4

Edar Algarrobo
IMFLUID

4

Edar Cómpeta
INITEK

4

Ispaster
INITEK

6

Gueñes
INTAGSA

1

Villa de Nefza (Túnez)
JOCA

2

Edar Cazorla
JOCA

1

Escuela de capataces
LUIS CORREA SALVARREY

2

---
OCISA

2

Vall d’Uxo
OMS SACEDE

1

EDAR MORAIRA - TEULADA ALICANTE
SOCAMEX

2

Simancas
SOCAMES, S.A.

1

S. Miguel de Salinas
SPA

3

Matadero de Casablanca
REYMAUX

2

Edar Villafranca
TAESA

1

Carnes Estelles
TEMAC

1

 
TRAGSA

1

REMODELACION EDAR CP PICASSENT
TRITIO, S.A.

1

EDAR Platea/Teruel
TRITIO, S.A.

1

Salamanca
URBASER

2

Aeropuerto Gran Canaria

In the biological treatment of wastewater, a series of processes are generated based on the cultivation of bacterial microorganisms for the elimination of organic matter, nitrogen and phosphorus. It is one of the most common treatments for its simplicity and low cost.

FILTRAMAS, S.A. has a wide variety of equipment for bacterial culture applied to the treatment of urban and industrial wastewater.

Band screens are those equipments, installed in a channel or , which has a series of filtering surfaces in continuous movement. Its mission is to extract the suspended solids of a certain size that accompany the effluent. There are several types of band screens, depending on the characteristics of the effluent and the installation:

The objective of this equipment is to protect the WWTP or pumping well from the possible arrival of large objects capable of causing obstructions in the different units of the installation. This operation consists of passing the waste water through a screen that separates and evacuates the bulky materials dragged along. They will retain large-sized solids such as branches, leaves, paper, tree roots, plastics, wipes, rags, etc., preventing damage and blockages to pumps, valves, pipes and other elements present in subsequent treatment processes of the purification plant.

These devices allow to continue filtering while performing self-cleaning, being especially suitable for those applications where continuous filtering is an important parameter of the process. Filtramas recommends the installation of its FB or FW in-line filters according to the flow and filtration needs.

Filter sieves offer high performance in the solid-liquid separation process. Our range of equipment responds to the different possible needs for each case.

FILTRAMAS, S.A. has a wide range of solutions for the transport and compacting of the waste extracted by its machines, in a clean and discreet. The conveying and compacting systems can be with screws with final draining zone or hydraulic presses.

The conveyor-compactor screws supplied by FILTRAMAS, S.A., coupled together with its equipment, allow us to obtain a totally clean and fair-faced installation. The screw loading openings are designed for coupling to the discharge opening of the extraction equipment (bars movable grilles or screens), and the intermediate spaces are covered by a fairing.

In any water treatment or purification plant, there is a continuous need to isolate or regulate the flow of water in the channels and manholes or holes in walls (wall gates). This function is carried out by means of the placement of gates and cofferdams.

The result of our experience is the establishment of a standardization that determines a satisfactory result with a simple construction. For this reason, Filtramas has been developing the manufacture of penstocks and flashboards.

Filtramas manufactures channel hatches, wall hatches and cofferdams for different applications and uses.

The accumulation of solid waste in water treatment requires effective mechanized solutions for its extraction. FILTRAMAS, S.A. has a wide variety of equipment for the dragging of solid waste.

In the biological treatment of wastewater, a series of processes are generated based on the cultivation of bacterial microorganisms for the elimination of organic matter, nitrogen and phosphorus. It is one of the most common treatments for its simplicity and low cost.

FILTRAMAS, S.A. has a wide variety of equipment for bacterial culture applied to the treatment of urban and industrial wastewater.

The dewatering of sludge is an essential process in the management of solid waste generated in water treatment. FILTRAMAS, S.A. offers different mechanized solutions to the problem according to the different possible needs.

FILTRAMAS S.A. has a wide variety of solutions for all kinds of problems associated with the treatment and cleaning of water, mud and sand. We develop our specialisation on the basis of the experience accumulated by our professionals, constant effort and close collaboration with our clients. FILTRAMAS S.A. perfects new products, looking for economic and effective solutions. Any problem that arises in the handling of fluids is carefully analyzed in order to find an economically balanced solution.